Expert Answers about Mazda

• Is 15' Long Zodiac Inflatable Boat Compatible With CE Smith Multi Sport Plus Boat and Kayak Trailer
• The max boat length for the CE Smith Multi Sport Plus Boat and Kayak Trailer # CE48870 is 14' so it will not work for your boat. Instead, you could use a trailer like the Malone MegaSport Kayak Trailer # MPG535 which has a maximum boat length of 20'. I'm not sure if the crossbars will work, that probably depends on your exact boat model. If you would rather have bunk boards you could add the Bunk Kit # MPG561
  view full answer...


• Trailer Hitch Receiver For a 2024 Kia Forte For Carrying a Wheelchair on a Cargo Carrier
• While the Curt Trailer Hitch Receiver # C55HR is confirmed to fit your 2024 Kia Forte it is only going to have a 1-1/4" receiver opening. And while there is an Adapter # HTAD which will change it over to a 2" receiver opening this does reduce the tongue weight capacity of the receiver by 50% which would only end up as 100lbs for the Curt # C55HR. We do have a 1-1/4" Cargo Carrier # C18110 but it does not have a ramp. This carrier weighs 30lbs so it would allow for 170lb electric wheelchair...
  view full answer...


• Replacement Shackle Straps For A 4" Long Shackle Strap
• Hey Corey, I'm not seeing a shackle strap with those dimensions. Your dimensions do sound suspiciously close to the Shackle Strap # TRSL275, which has 2-3/4" distance from center of the two holes, is 4" long overall, and has a 9/16" bolt hole. I would double check your measurements and if you find it's still the same then you can try reaching out to Dexter or MORryde to see if they might offer them directly.
  view full answer...


• How Much Does The Fogatti RV Water Heaters LSB64FR Weigh?
• The Fogatti RV Water Heater 41,800 Btu - White # LSB64FR weighs 30 pounds. This goes for the black # LSB44FR as well.
  view full answer...


• How Much Does The Kuat Transfer V2 KU64FR weigh?
• The Kuat Transfer V2 # KU64FR weighs right at 26 pounds.
  view full answer...


• How Much Does The Curt 7 Way Wiring C56431 Weigh?
• The Curt T-Connector Vehicle Wiring Harness # C56431 weighs in at 1.5 pounds, so nice and light.
  view full answer...


• How Much Does The BAKFlip MX4 Hard Tonneau Cover BAK48120 Weigh?
• The BAKFlip MX4 Hard Tonneau Cover # BAK48120 weighs in at 70 pounds.
  view full answer...


• Will Brophy Camper Tie-Downs # HSSF Fit A 2018 GMC Sierra 2500HD
• Hey David, The Brophy Slide In Camper Tie-Downs # HSSF could potentially work but you'll first want to ensure you have enough clearance for them to fit up against the inner lip of the bedrails and clear the side body of the bedrails. I've attached a diagram below of their dimensions so you can measure your bedrails and confirm fitment. To complete the setup Brophy also offers turnbuckles with part # TDHP.
  view full answer...


• Solution for Replacing a Torsion Axle on a PWC Trailer
• You're welcome Dan! Sorry we do not have anything to offer that will be a direct replacement of your torsion axle. The only solution I have is to replace it with a axle-less option like the Timbren 2,200 lbs item # ASR1THDS01 or the 3,500 lbs item # TASR35HDS04. These are independent systems that do not require an axle shaft so they fit any trailer width. While they may seem pricey if you are not able to source a replacement torsion axle and have to have one customized these are a comparable...
  view full answer...


• Recommended Replacement Dexter Axle W/ E-Z Lube Spindles for a Axis Products 3.5K Axle
• Eddie, it sounds like you're looking for the Dexter Trailer Axle w/ Electric Brakes # 35545E-ST-EZ-89. This is a 3.5K Dexter axle that has E-Z Lube spindles, with a 5 on 4 1/2" bolt pattern. This axle has a 89" hub face to hub face measurement, 74" spring center to spring center measurement, and a 1 1/16" spindle size.
  view full answer...


• Recommended Air Bag Suspension for a 2008 Ford F-250
• Those don't fit a 2008 Ford F-250. Instead you will need the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers item # AL88398. These work with the 4WD models and have the same 5,000 lbs capacity. If your F-250 is a 2WD you'll need item # AL88212. Since your F-250 has a 4-1/2" lift you will need to add a spacer to the rear end to compensate for the extra space in the suspension. There's two options and which one you need will depend on how tall the lift actually...
  view full answer...


• Dimensions of the Rampage Tow Hook Kit for Jeeps
• Hey Herb, I went out to our warehouse and measured the length of the Rampage Tow Hook Kit for Jeep # RA7505 and measured 11 1/4" overall and 6 1/2" from the top of the curve to the bottom.
  view full answer...


• Weight Ratings for Ladder Racks on 2017 Ram 2500
• Many of our ladder racks only show an on-road and off-road weight rating which is what you're seeing. Most of the time that is the rating people are looking for since they're using it to haul equipment around with them. The static rating is typically higher and for most of our ladder racks it is listed in the instructions. The Yakima OutPost HD Overland Truck Bed Rack # Y01152-58 you looked at has a static load rating of 800 lbs. The same is true for the Yakima OverHaul HD # Y01151-58....
  view full answer...


• Replacement Tail Light for a 2019 Coachmen Freelander 21QB Motorhome
• Thanks for reaching out, Wendell! According to my research the Triple LED Trailer Tail Light # CE44VR looks very similar to what comes on your 2019 Coachmen Freelander 21QB. As long as the 14" long x 6-7/8" tall x 1" deep dimensions match what you have then you'll be able to use this on your motorhome!
  view full answer...


• Recommended Trailer Hitch for a 2002 Dodge 2500 Roadtrek 170
• Robert, we don't have tow bumpers for your 2002 Dodge 2500 Roadtrek 170, unfortunately. What you could do instead is install a hitch like the Multi-Fit Motor Home Trailer Hitch # 82201 and slap a ball mount in there # DT49MR and you'd be all set. This is a multi-fit hitch that has a 3.5K capacity and can adjust anywhere from 47" to 72" wide, so you'd just need to measure your frame width to verify.
  view full answer...


• What Size Trailer Wheel/Tire has Bolt Pattern 5 on 4-3/4 inch Available
• The only size wheels we have with a 5 on 4-3/4 inch bolt pattern is the 15 inch wheel size like with the part # KE79JR which has the tire size ST205/75R15 mounted on it.
  view full answer...


• Replacement Tack Room Door Latch For A Featherlight Trailer
• We may have some potential options for replacing the tack room door lock on your Featherlight trailer. Is the 5" L x 5" H dimension you gave for the door cutout or the lock itself? The best way to find the right replacement lock is to go by the cutout size. If your cutout is 5" x 5" we do not have a lock that will fit those exact dimensions. The closest thing we have is the Bauer Products Motorhome Door Lock # BA64FR which will fit a 5-1/4" wide x 4-1/2" tall cutout. Is it made for a...
  view full answer...


• Parts Needed to Convert a Tandem Axle Trailer to a Triple Axle Trailer
• Daniel, you can add a third axle but you're going to want to keep all of your axles the same size. So if you wanted 6K axles instead of 5.2K then you'd want to swap the other two as well. With that said, to add your third axle you're going to need the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles # APUBR-8, the Triple-Axle Trailer Hanger Kit for Double-Eye Springs # APTT5, and the 6-Leaf Double-Eye Spring for 5,300-lb Trailer Axles # e76SR. For the axle itself, let...
  view full answer...


• Why Is The Flint Hill Goods Loading Ramp Set FHG73ZR Limited To A 35" Loading Height
• Hey Monte that is a really good question. I double checked with one of our product engineers and this is what I was told in regard to the Flint Hill Goods Loading Ramp Set # FHG73ZR. The 35" loading height puts the ramp at the appropriate angle to where it can be used up to its full capacity. Going with a higher loading height makes the ramp more vertical. This does not mean that the ramp is automatically going to fail if you put it at 36", but it is not going to be ideal for this ramp...
  view full answer...


• Solution for Replacing Welded-On Trailer Brakes on Old Car Trailer
• That was enough information right there. If it is welded to the axle a modern replacement won't work. Unless you can find parts at a scrap yard you won't be able to get replacement parts for those brakes to rebuild them either. You will need to replace the axle like I mentioned before. You need the same length axle you have now, which is the hub face to hub face measurement, along with the same capacity. You can try to see if there is an axle tag on there identifying it. If not, it might...
  view full answer...